로고

로고
  • 커뮤니티
  • 제품문의
  • 커뮤니티

    제품문의

    How to eliminate el

    페이지 정보

    profile_image
    작성자 EQiblydup
    댓글 댓글 0건   조회Hit 58회   작성일Date 25-01-14 10:27

    본문

    <h2>  Employing the Balanset-1A System  </h2>
     
    <h3>  Equipment Preparation  </h3>
    <ul>
    <li>  vibration sensors, optical speed sensor, magnetic base, software package, and included accessories.  </li>
    <li>  Establish a USB connection between the instrument and the computer, ensuring the software is set up properly.  </li>
    </ul>
     
    <h3>  Sensor Installation  </h3>
    <ul>
    <li>  Mount the vibration transducers securely on the machine's housing where vibrations are most pronounced, typically near the bearings.    </li>
    <li>  Position the laser tachometer (phase angle sensor) so that it is aimed at the rotor. Attach reflective tape to the rotor for accurate phase angle reading.    </li>
    </ul>
     
    <h3> Software Startup  </h3>
    <ul>
    <li>  Initiate the Balanset program on your computer.  </li>
    <li>  Select the appropriate balancing mode: single-plane or two-plane, depending on the rotor type and your specific requirements.    </li>
    </ul>
     
    <h3>  Taking Baseline Vibration Readings  </h3>
    <a href="https://vibromera.eu/wp-content/uploads/2024/11/2-Camera_01.png" target="_blank">
    <img src="https://vibromera.eu/wp-content/uploads/2024/11/2-Camera_01.png" alt="2-Camera_01" style="width: 50%; display: block; margin-bottom: 10px;">
    </a>
    <ul>
    <li>  Bring the rotor to its normal operating rotational frequency.  </li>
    <li>  The software will measure the vibration level, rotational speed, and phase angle. This data establishes the current imbalance condition.    </li>
    </ul>
     
    <h3> Mounting the Test Weight  </h3>
    <a href="https://vibromera.eu/wp-content/uploads/2024/11/3-Camera-2_01.png" target="_blank">
    <img src="https://vibromera.eu/wp-content/uploads/2024/11/3-Camera-2_01.png" alt="3-Camera-2_01" style="width: 50%; display: block; margin-bottom: 10px;">
    </a>
    <ul>
    <li>  Halt the rotation and mount a test weight at a designated position on the rotor, with the weight's value entered into the software (usually in grams).  </li>
    <li>  Run the rotor again, allowing the software to measure the effects of the trial weight on vibration and phase.  </li>
    </ul>
    <a href="https://vibromera.eu/wp-content/uploads/2024/11/5-Camera_01.png" target="_blank">
    <img src="https://vibromera.eu/wp-content/uploads/2024/11/5-Camera_01.png" alt="5-Camera_01" style="width: 50%; display: block; margin-bottom: 10px;">
    </a>
     
     
    <h3> Calculating the Correction Weight  </h3>
    <ul>
    <li>  The software uses the measured values to automatically compute the necessary compensating weight's magnitude and placement angle.  </li>
    <li>  The calculated values are presented on-screen in both numerical and graphical formats.  </li>
    </ul>
    <a href="https://vibromera.eu/wp-content/uploads/2024/02/Bs1ManualEngV156-May2023-10448629.png" target="_blank">
    <img src="https://vibromera.eu/wp-content/uploads/2024/02/Bs1ManualEngV156-May2023-10448629.png" alt="Bs1 Manual" style="width: 30%; display: block; margin-bottom: 10px;">
    </a>
     
    <h3> Mounting the Compensating Weight  </h3>
    <ul>
    <li>  Attach the computed compensating weight to the rotor as indicated by the software's output.  </li>
    <li>  You can conduct interim measurements to confirm that the imbalance is decreasing as expected.  </li>
    </ul>
    <a href="https://vibromera.eu/wp-content/uploads/2024/11/1-Camera-2_01.png" target="_blank">
    <img src="https://vibromera.eu/wp-content/uploads/2024/11/1-Camera-2_01.png" alt="1-Camera-2_01" style="width: 50%; display: block; margin-bottom: 10px;">
    </a>
     
    <h3> Verification and Balancing Completion  </h3>
    <ul>
    <li>  With the compensating weight attached, operate the rotor and assess the level of any residual vibration.  </li>
    <li>  If the measured vibration falls within the tolerance defined by ISO 1940, the balancing process is considered successful.  </li>
    <li>  Should the vibration still be excessive, repeat the balancing steps, making further adjustments to the corrective weight as needed.  </li>
    </ul>
     
    <h3> Generating a Documentation of the Balancing Results  </h3>
    <ul>
    <li>  The program stores the balancing data, allowing you to generate and print a comprehensive report including vibration measurements, corrective weight details, and its angular placement.  </li>
    </ul>
     
    <h3>  Post-Balancing Checklist  </h3>
    <ul>
    <li>  Verify the secure attachment of all balancing weights and measurement sensors.  </li>
    <li>  Confirm that the rotor spins freely and quietly, without any unusual sounds or vibrations.  </li>
    <li>  If the rotor operates within a larger assembly, check the functionality and interplay of all interconnected parts.  </li>
    </ul>
     
    <p>  By implementing this method, you can effectively eliminate imbalance, reduce vibration levels, and increase the lifespan of the machinery.  </p>
     
     
     
     
    Instagram: https://www.instagram.com/vibromera_ou/
    Youtube : https://youtu.be/guA6XJ-ArZM?si=vmkuX7RILzKBl0zL 
    Our website about  <a href="https://vibromera.eu 
    "> Correction weights </a>
    Machinio: https://www.machinio.com/listings/98380186-portable-balancer-vibration-analyzer-balanset-1a-full-kit-in-portugal
    Facebook: https://www.facebook.com/marketplace/item/350151228150722

    댓글목록

    등록된 댓글이 없습니다.